Login
Registration
Profile Informations
Login Datas
or login
Product Description
Details
Overview
ITDB02-2.8 module is 2.8" TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is ILI9325DS. It supports 8bit data interface with 4 wires control interface. Moreover, this module contains the touch screen and SD card socket.
ITDB02-2.8 is supported by UTFT Library.
Hardware
|
Pin |
Type* |
Description |
|
GND |
G |
Ground |
|
VCC |
P |
5V Power Supply pin |
|
NC |
- |
No connection |
|
RS |
I |
Data/Command selection |
|
WR |
I |
Write signal enable, low active |
|
RD |
I |
Read signal enable, low active |
|
DB8 |
I |
Data Bus |
|
DB9 |
I |
Data Bus |
|
DB10 |
I |
Data Bus |
|
DB11 |
I |
Data Bus |
|
DB12 |
I |
Data Bus |
|
DB13 |
I |
Data Bus |
|
DB14 |
I |
Data Bus |
|
DB15 |
I |
Data Bus |
|
CS |
I |
Chip Selection，Low level active |
|
NC |
- |
No connection |
|
LED |
P |
Backlight |
|
NC |
- |
No connection |
|
DB0 |
- |
No connection(8bit mode) |
|
DB1 |
- |
No connection(8bit mode) |
|
DB2 |
- |
No connection(8bit mode) |
|
DB3 |
- |
No connection(8bit mode) |
|
DB4 |
- |
No connection(8bit mode) |
|
DB5 |
- |
No connection(8bit mode) |
|
DB6 |
- |
No connection(8bit mode) |
|
DB7 |
- |
No connection(8bit mode) |
|
T_CLK |
I |
Touch clock |
|
T_CS |
I |
Touch chip selection |
|
T_DIN |
I |
Touch data input |
|
T_BUSY |
O |
Touch status |
|
T_DOUT |
O |
Touch data output |
|
T_IRQ |
O |
Touch interrupt |
|
SD_SO |
O |
SD MISO |
|
SD_SCK |
I |
SD SCK |
|
SD_SI |
I |
SD MOSI |
|
SD_NSS |
I |
SD NSS |
|
NC |
- |
No connection |
|
NC |
- |
No connection |
Additional Information
Additional Information
| Discontinued | Yes |
|---|---|
| Link Wiki | No |
| Display Resolution | 320 * 240 |
| Display Interface | Parallel 8 Bit |
| Screen Type | Touch Screen |
| Display Controller | ILI9325C |
| TFT display interface | Parallel 8 bit |
| Display Size | 3.2” |
| Board Size | 76 x 51mm |
| Expand |
|
| Weight | 60 g |
Reviews
Customer Reviews
- Very nice product Review by Famory
-
Very nice product. The LCD demo worked almost instantly after installing Wriring Pi. I have also tested with the Raspberry Pi and the fbtft library. The library default pins are for a Raspberry Pi v1. After searching for some time, I finally found the settings for the v2 and it works perfectly.
Some minor remarks however to improve the product:
- adding some holes on the corners (or only on the top) would help to attach the card
- the documentation is a little bit week regarding the support of the SD card
(Posted on 7/17/2013) - Nice Review by Murat
- Wonderful and a nice product. (Posted on 12/10/2012)
- Recommended Review by Morn
- items are as described and quick shipping. Hope to do business again (Posted on 8/20/2012)
Guess you like
Empty.
Recent History
Empty.
